@Razzmatazz

Factory-style switch-blank panel for a flush-mounted combined USB and 3.5 mm auxiliary extension socket.

Panel for installing a USB socket beside the rear-heater switch or in place of the coin holder in the centre console.

Workshop socket for removing and installing the radio-antenna retaining nut.

Three ashtray-replacement panel variants for adding rear-seat USB outlets, including switched and mirrored switched layouts.

Interference-fit insert for the opening above the radio, with interchangeable mounts for a hands-free microphone and magnetic phone holder. The revised body includes pockets for two 5/16 by 1/8 inch retaining magnets.

Threaded replacement cap for the power-seat drive screw.

Hands-free funnel that screws into the 37 mm by 3 mm-pitch oil-filler opening on the 1FZ-FE engine, keeping it seated above the rocker-cover baffle.

Replacement release lever for the lower tailgate, supplied with editable STEP source. The spline fit may need adjustment for individual printers.

Replacement blanking plug for unused rectangular dashboard switch positions.

Three cup-holder insert variants for the square centre-console opening, including a larger rounded recess and a version with an accessory slot.

Replacement latch for the storage box between the front seats.

Deeper replacement pocket for the opening above the stereo, with a rear cable pass-through.

Replacement latch for the fuel-filler door.

Rear support bracket for the power-seat threaded drive rod. The creator recommends full infill and notes that the centre bore may need adjustment.

Middle- and side-vent repair inserts that replace crumbled pivot plates and provide new pins for drilled vent vanes.

Blanking cover for the third-row ashtray opening when the original tray cannot be retained.

Insert for the front compartment of the factory centre console, with two 72 mm cup recesses and a vertical phone slot.

Replacement plastic captive nuts for securing the grille, headlamps and front running lights. The creator recommends weather- and heat-resistant material.

Pair of rails for replacing the ashtray with a CB radio or another accessory approximately 115 mm wide.

Replacement interior-light cover and flexible gasket for fitting a low-cost LED panel in place of the original lamp assembly.

Replacement grommet and retaining catch for the bonnet support rod. The creator recommends weather- and heat-resistant material.

Three replacement plastic fasteners for the grille, lamp and bulb-holder positions on a 1987 vehicle.

Three blanking-plug variants for the small and large dashboard switch openings, including a small plug with a centre hole.

Bracket for installing a 2 1/16-inch Speedhut or similarly sized 53 mm tachometer in the original instrument cluster.

Left- and right-hand two-piece inner housings for repairing brittle side-marker assemblies, with alternate bulb-socket openings and blank editable socket source.

Two-piece replacement fuse-box cover with raised fuse-position text, modelled from a damaged original cover.

Clip for mounting a 31 mm Element fire extinguisher, flashlight or similar cylindrical item to a 26.1 by 4.9 mm seat-bracket crossbar.

Five-piece replacement for the original small cup holder, split for compact printers and designed for larger cups and bottles. The left- and right-hand upper pieces can be mirrored for left-hand-drive fitment.

Replacement mounting bracket for the rear camera.

Separate front- and rear-door spacers for installing 8-inch aftermarket speakers while preserving window-glass clearance.

Replacement internal drive gear for the powered radio antenna assembly.

Replacement knob for the second-row audio-control unit in the centre console, with a 4.85 mm inner bore for a nominal 4.7 mm shaft.

Replacement access door for the factory-style cabin-filter retrofit opening in the evaporator cover. This version is slightly oversized for an opening cut to the moulded guide line.

Replacement latch for the centre-console storage box, modelled for the BJ73.

Three-piece console extension for a VDJ79 pickup, with a pen slot, drink holder, glasses pocket, dual-USB socket position, business-card dispenser, phone pocket, removable utility tray and hidden storage. It joins with a dovetail and fits between the original console and cup holder without vehicle modification.

Replacement latch for the centre-console storage box on 1990–1995 vehicles.

Three-piece brace, locating ring and locking wedge for mounting a 175-amp electrical quick-disconnect socket in the grille on 1990–1995 vehicles.

Three-piece brace, locating ring and locking wedge for mounting a 50-amp electrical quick-disconnect socket in the grille on 1990–1995 vehicles.

Two dashboard inserts: one holds a replacement accessory-power socket or USB charger, and the other accepts a 52 mm auxiliary gauge.