Toyota Tacoma 3D-printable parts

Replacement clip for securing the front turn-signal assembly, with provision for an M3 retaining screw.

Replacement plastic screw-retaining clip for the removable panel below the headlamp on 1996–2000 vehicles.

Replacement cap for the windscreen-washer fluid reservoir, modelled and tested on a 2001 vehicle.

Workshop drivers for installing the driver- and passenger-side axle seals in the 7.5-inch front differential. Quarter-inch and half-inch extension-drive variants are included.

Magnetic phone-mount base that replaces the upper driver-side grab-handle screw cover on 1997–2004 vehicles.

Replacement trim cap for the screw opening in the interior door-handle surround, modelled from a 2002 vehicle.

Press-fit replacement knob for the heater, fan-speed or airflow-control shafts on 2000–2004 vehicles.

Single-DIN dashboard insert supplied as a plain storage pocket and as a panel for two compact voltmeters and a switch.

Replacement passenger-side clip that secures the interior door handle to its release cable, modelled from a 2003 vehicle.

Weighted friction-fit phone holder for the coin tray beside the shifter, with space for a wireless-charging module.

Pair of twist-on mounts for securing a full-size flashlight between 10 mm headrest posts.

Four fitted insert layouts for carrying Yeti-style tumblers or Hydro Flask bottles in the centre cup holders.

Clip-on holder for a compact Bluetooth headset, shaped for the dashboard vents used from 2001–2004.

Replacement latch for the sliding rear window, confirmed by the creator on 1996 and 1998 vehicles.

Flush cover for the opening left after removal of the bedside storage cubby.

Fitted centre cup-holder insert with storage for coins, a pen and a compact multi-tool.

Clip-in adapter for fitting a dual-USB extension socket into a factory dashboard switch opening without modifying the original trim.

Centre-console switch blank replacement that accepts an RJ-series keystone connector for radio or data wiring.

Three centre-console switch-insert bases ranging from a minimal frame to a complete blank for custom controls.

Driver sized for installing the transfer-case output seal on a 2006 vehicle without damaging the sealing lip.

Three-piece centre-console organisation system comprising a deep box, false-bottom divider and removable upper tray.

Snap-on black cap for the exposed upper shift-boot collar after fitting an aftermarket knob to the six-speed manual transmission.

Threaded oil-filler adapter and matching funnel for the four-litre engine used in this generation.

Lengthened replacement trim clip for securing the centre head-unit bezel without breaking or dropping into the dashboard.

Five fitted tray layouts for organising the deep centre-console compartment, including divided and coin-storage versions.

Replacement divider for the centre cup holder, supplied in standard and taller versions.

Replacement overhead-console panel with openings for two compact aftermarket switches on 2016–2019 vehicles.

Fitted dashboard mount for a Tekonsha P3 controller that replaces the small pocket beside the steering wheel.

Five-piece 120 mm ventilation-fan mount and air-guide set for a regular-cab SnugTop camper-shell side window.

Pull-out coin drawer sized for an unused dashboard switch opening.

Recessed slip-on sleeves that enlarge the factory radio control knobs.

Lightweight framed dashboard mount for a compact CB or FTM-400XDR radio control head.

Small L-shaped rain shield for an aftermarket reversing camera fitted to this generation.

Two-piece conversion set that adapts the 2017 centre-console cup holders for a 32-ounce insulated bottle.

Replacement end cap for the cargo-bed utility-track assembly used through the 2020 model year.

Retaining ring for the 2020 dashboard drive-mode selector to reduce accidental rotation between two- and four-wheel drive.

Clip-on holder that keeps the tethered fuel cap secured to the inside of the open fuel door.

Adapter that secures the 2016-and-later ignition key blade in a folding key-organiser body.

Drain fitting that joins the tonneau-cover hose to the factory bed drain without drilling.

Fitted clip for storing a cylindrical flashlight within the cab.

Four-sided insert that centres a 14-ounce handled tumbler in the 2017 middle console cup holder.

Two height options for angling a threaded oil funnel away from surrounding engine-bay components.

Low-profile magnetic phone-mount base shaped for the 2020 dashboard.

Dashboard bracket for positioning a compact auxiliary-camera display above the centre controls.

Small clip for routing accessory wiring neatly along the rear-view-mirror stem.

Four-piece phone dock concealed in the dashboard cubby, with a fitted plate, retaining clip and mounting clip.

Two cover variants for closing the rear centre-console drink holder when it is not in use.

Flexible clips that hold the spring-loaded cup-holder spacers retracted.

Three fitted drawer sections that divide and organise the glovebox.

Adapter that routes a retractable tonneau-cover drain hose through the factory bed drain.

Fitted pad for installing a 15-watt magnetic phone charger in vehicles without the factory wireless charger.

Drain connector for routing the hoses from a roll-up tonneau cover on a 2025 bed.

Small fitted insert that removes glovebox movement and rattling, modelled on a 2025 vehicle.

Pull-out coin drawer for the small dashboard storage opening.

Seat-back hanger for supporting a hard-hat bag or other light equipment.

Hook for suspending light bags from either front seat.