Toyota 4Runner 3D-printable parts

Replacement latch for the centre-console storage box on 1990–1995 vehicles.

Three-piece brace, locating ring and locking wedge for mounting a 175-amp electrical quick-disconnect socket in the grille on 1990–1995 vehicles.

Three-piece brace, locating ring and locking wedge for mounting a 50-amp electrical quick-disconnect socket in the grille on 1990–1995 vehicles.

Two dashboard inserts: one holds a replacement accessory-power socket or USB charger, and the other accepts a 52 mm auxiliary gauge.

Replacement bushing that removes excess play from the gear-shift lever.

Multi-piece phone mount that replaces the dashboard clock insert. Files include stud and printed-ball mounting options

Clip-on brace that holds the rear hatch fully open when worn gas struts can no longer support it.

Replacement bushings and keeper for the upper rear-hatch gas-strut mounting pin, with factory-style and revised versions.

Adapter for installing the later 3.4-litre mass-airflow tube in the earlier air-cleaner housing while retaining the original intake hose position.

Protective pocket that restores a key-ring attachment point to a remote fob with a broken mounting loop. The source was designed around a 1999 remote.

Replacement body-pressure vent with sliding closure, fixed-cover and drain-tube versions.

Four mounting pieces for suspending fishing rods inside the cargo area using a 27-inch length of half-inch PVC pipe.

Replacement trim cover for the fastener in an interior grab handle, modelled from a 1998 vehicle.

Four-position switch panel for the cubby in the later centre console, designed for the 1998–2000 console layout and original-style switches.

Left- and right-hand adapter plates for mounting 6.5-inch rear speakers in the original rear-door positions.

Replacement console cup-holder insert with two small pen or straw openings and a card slot.

Repair insert for the driver's footrest trim.

Driver-side and passenger-side replacement adjusters for the two central dashboard air vents.

Clip-in cover for an unused eight-by-four-inch dashboard stereo opening.

Driver-side and passenger-side mounting adapters for installing one-inch aftermarket tweeters in the front doors.

Multi-piece ScanGauge II mount that occupies a left-hand-drive dashboard switch position and includes a replacement instrument face.

Mounting block for installing an AT-5888UV radio control head in the centre-console storage compartment.

Mounting block for securing an AT-5888UV radio body behind the right-hand rear cargo compartment.

Three-piece tray, latch and strap-stay set for securing a medium first-aid kit behind a front-seat headrest.

Front and rear spacer blocks for fitting an aluminium storage bar along each side of the cargo compartment.

Bracket for attaching a small auxiliary light to the factory roof rail, with an integral wiring channel and cable-management loops.

Replacement handle for the rear-seat tilt mechanism, designed around the ten-millimetre square release post in a 2007 vehicle.

Fitted organiser for the shallow console space ahead of the cup holders, with compartments for small everyday-carry items.

Mount for replacing the sunglasses holder with a six-switch sPod controller on vehicles without crawl control.

Low-profile rear dash-camera mount that reuses the original headliner fastener and provides a pad for a Viofo-style camera.

No-cut panel for two Contura-style switches in the small console box above the driver's cup holder on 2014-and-later vehicles.

Contoured spacer mount for attaching a ScanGauge II to the curved upper steering-column trim.

Two-piece dashboard mount for a Choetech three-coil wireless charging dock, modelled and installed on a 2016 vehicle.

Friction-fit dashboard blank insert that retains the USB cable end supplied with a T10 replacement head unit.

Plug for the cargo-cover recess with a socket for half-inch PVC tube or 26 mm pole

Replacement push button for the left or right folding rear-seat release on 2010–2018 vehicles.

Replacement left-or-right cargo-compartment hook with a deeper profile for retaining cover straps, modelled on a 2015 Limited.

Fitted block that turns the narrow centre-console pocket into divided storage for coins, pens and other small items.

Small storage cubby for the unused dashboard recess next to the USB charger.

Multi-piece passenger-side centre-console bracket for an adjustable CB radio installation.

Three centre-console cup-holder reducers for small tumblers, large tumblers and handled mugs.

Overhead-console insert for a Kenwood-style aftermarket microphone, replacing the factory microphone position.

Trim cover for the exposed side-panel hinge opening after removal of the rear seats.

Clip-in phone mount for the dashboard vent opening, supplied in plain and trim-labelled variants.

Replacement overhead-console cover for the SOS switch position on 2010–2022 vehicles.

Replacement interior fuse-box cover for a 2020 vehicle, intended to be opened locally for an add-a-fuse lead without modifying the original cover.

Multi-piece holder that mounts a rectangular facial-tissue box behind the rear display using side fingers and a profiled support.

Fitted centre-console tray for two JSAUX 15-watt wireless charging pucks, designed around the console in a vehicle without the factory wireless charger.

Replacement four-position ignition-wire separator that clips to the timing cover on vehicles equipped with the 3VZ-E engine.

Replacement 10 mm square plastic body grommet for number-10 screws used on exterior trim such as side-marker lamps.

Replacement clip that secures the front grille to the body.

Two-piece sliding cup holder that installs in the original ashtray bracket, with alternative threaded rear pieces for different bracket wear.

Replacement retaining clip for the removable-roof B-pillar trim.

Replacement clear lens for the interior light above the rear deck.

Replacement blanking cap for an unused rectangular dashboard switch opening.

Dashboard switch-opening adapter for an RJ45 keystone inline coupler, supplied in standard-snap and tight-snap versions.

Replacement retaining clip for the dashboard heating and ventilation controls.

Replacement threaded knob for releasing and folding the rear seat.