Mechanical — 3D-printable Toyota parts

Tall Engine-Bay Fuse-Box Cover designed for the 2011-2017 Toyota Camry (XV50). Designed specifically as a taller 2012 Camry fuse-box cover to clear fuse taps. Aftermarket modified cover

Cabin Air Intake Screen designed for the 2006-2011 Toyota Camry (XV40). Tight-fit intake screen measured on a 2011 sixth-generation Camry. Aftermarket critter/leaf screen, not an OEM replacement.

Under-Cowl Cabin Air Filter Frame designed for the 1996-2001 Toyota Camry (XV20). Author identifies a two-piece glue-together cabin filter frame for a US 2000 XV20 Camry under the passenger-side cowl. Frame/filter interface should be checked for sealing and water drainage.

A printable alternator main-wire cover documented by the original creator for 2013-2017 Corolla Toyota Corolla fitment. Use PETG/ABS or higher-temperature material, as source advises.

A printable intake maf tube documented by the original creator for 2009-2013 North-American E140 Wide Toyota Corolla fitment. Engine/sensor configuration-specific

A printable ecu connector protective cover documented by the original creator for 2009-2015 Toyota Prius fitment. Prefer original over logo remix 5410499

Coil-Pack Wire Holder for Toyota Celica, mapped to the T200 generation based on the source fitment information. 6th generation / creator's 1994 Celica. Replacement under-hood wire holder

TRD-Style Rear Strut-Brace Accessory Clips for Toyota MR2, mapped to the W20 generation based on the source fitment information. Source says the clips mount accessories to TRD or replica SW20 rear strut braces. Aftermarket clips

Odyssey-PC680 Battery Adapter for Toyota 86 / GR86, mapped to the ZN8 generation based on the source fitment information. Source explicitly states 2022/2023 GR86/BRZ

Sound-Pipe Cabin Plug for Toyota 86 / GR86, mapped to the ZN6 generation based on the source fitment information. Source explicitly identifies GT86/FR-S/BRZ.

Intake-Resonator Block-Off Plate for Toyota 86 / GR86, mapped to the ZN8 generation based on the source fitment information. GR86 naming and 2022 source date point to ZN8, but the source text gives no explicit model year. Confirm bolt spacing before import.

Replacement ABS mounting block for the harness cover on the 2000–2005 Toyota RAV4.

Mirrored left- and right-hand replacement radiator-support extensions for the second-generation Celica Supra, modelled from an original part and reference photographs.

Flexible replacement support that secures the brake-vacuum hose to the remaining factory bracket post, modelled and installed on a 2006 vehicle.

Two height options for angling a threaded oil funnel away from surrounding engine-bay components.

Threaded oil-filler adapter and matching funnel for the four-litre engine used in this generation.

Workshop drivers for installing the driver- and passenger-side axle seals in the 7.5-inch front differential. Quarter-inch and half-inch extension-drive variants are included.

Replacement intake cover for the accessory snorkel, with additional retention clips and compatibility with the original cover mounting geometry.

M37-by-3 threaded oil funnel for the engine filler neck, supplied in handled and compact versions.

Split replacement spacer that restores adjustment range when the original rubber throttle-cable spacer deteriorates.

Replacement protective cover for the original alternator overrunning clutch.

Replacement four-position ignition-wire separator that clips to the timing cover on vehicles equipped with the 3VZ-E engine.

Adapter for installing the later 3.4-litre mass-airflow tube in the earlier air-cleaner housing while retaining the original intake hose position.

Replacement access door for the factory-style cabin-filter retrofit opening in the evaporator cover. This version is slightly oversized for an opening cut to the moulded guide line.